#HOW TO MASTER VOCALS IN FL STUDIO HOW TO#

Unfortunately, they do not work in this modern production era anymore. The reason why a lot of amateur engineers canвЂ™t get a really good vocal mixing sound is because a bunch of the stuff that we read online concerning mixing years ago donвЂ™t work.

#HOW TO MASTER VOCALS IN FL STUDIO HOW TO#

HOW TO MAKE YOUR VOCAL SOUND PROFESSIONAL Request a new vocal recording with a better performance. iZotope Exciter, UAD SuderДЄfter, you have done all these steps, if you listen and think your vocal still donвЂ™t sound professional, IвЂ™ ll recommend:Дouble up on 1 or 2 of the steps above for more hyper processed sound, but use them in parallel to retain some dynamics.

Plugins recommendations: Waves Kramer tape, Waves J37 Tape, Decapitator, Fabfilter Saturn. You may use tape saturation plugins, or transformer or tube saturation whichever you have available is fine. In this case, we are using Ableton Live Saturation plugin in analog mode. Saturation is adding slight form of distortion which creates pleasant-sounding harmonics. Warm up the sound and increase pleasant harmonics

Reduce woof-ness and boxiness : 200Hz - 400Hz Remove plosives and rumbles: Low Cut / HP Pass Filter 85Hz - 150Hz (depending on the gender) Use a very narrow bandwidth, cut between 2db to 6db depending on the vocal. I would recommend: Be very gentle when you remove these frequencies. I would generally do a sweep around these spots to find any annoying frequencies that need to be taken out. Always check around 200Hz - 400Hz area, thatвЂ™s where the boxiness lives.ДЄnd around 1kHz - 4KHz area for harsh and honky frequencies. I will give you some pointers and some frequencies to look for. Once we are done, we will move up to the next octave up. The first plug-in in the chain is a corrective EQ, and what weвЂ™re doing here is to remove any frequency that might be bugging us in the vocal.ДЄnd, also we are rolling off the low bottom frequency around 80Hz -150Hz, depending on the vocal, also depending on the gender. If this is a singing vocal, make sure you have a pitch correction done, and tune all the vocals, the vocal melodies and harmonies in tune with all the key of the song.ДЄll right let's get to the vocal mixing section. In the performance editing phase, you should fix any pitch or timing errors in your vocal recording. So after youвЂ™ve got all the editing done on your vocal recording, then we can start prepping the vocal for the mix. I'm sure you have read this in a many blogs out there but I just want to cover all the bases. Repair any damages, Use iZotope RX to repair clicks, clips, noise, and plosives too.В If there are any room tones or annoying frequencies, use your EQ to notch them out. In the editing phase, you want to listen to the entirety of the vocal recording.В Listen for pops, clicks, clips or any annoying frequency that may poke at you. If you're not in a good room, you may run the risk of recording all surrounding noises too.ДЄfter you've achieved a very good vocal recording, the next phase is editing. If you may record low but you want to be mindful of the room you are in. Record at decent gain level.Дon't record a too hot signal nor a too low signal. The next thing to take note of is your gain staging. You may have an acoustic treatment which is rather expensive, but if you can't afford it, just make sure you have a room that is semi dead, not too reflective or echoey. Saturation - warm up the sound and increase pleasant harmonics The first step to getting a good vocal sound begins with a good vocal recording.Д®nsure you record with a good microphone in a good room. Tonal Density Compression - create a more compactness in sound qualityД§. De-Esser - reduce and tame sibilance or harshnessДҐ. Tonal Shaping EQ - bring out presence, midrange power, and airД¤. Dynamic Peak Compression - tame unruly peaks for more consistent vocalДЈ. Corrective EQ - remove annoying frequenciesДў.

How to master vocals in fl studio